产品特性测试 | 是否进口否 |
产地广东 | 加工定制否 |
品牌百航 | 型号BH-603 |
测试行程100cpm | 测试速度100cpm |
类型耐磨测试 | 外形尺寸1500*1100*1050mm |
重量350kg | 适用范围测试 |
装箱数1 |
产品特性测试 | 是否进口否 |
产地广东 | 加工定制否 |
品牌百航 | 型号BH-603 |
测试行程100cpm | 测试速度100cpm |
类型耐磨测试 | 外形尺寸1500*1100*1050mm |
重量350kg | 适用范围测试 |
装箱数1 |
一 概述:本测试机广泛用于测试地板的脚轮耐磨性,通过一定规格的脚轮在一定转速、一定负载、一定运动轨迹的情况下摩擦地板试样,完成累计的试验次数后自动停机来观察试样变化,评估试样耐磨性能,具有实验循环计数累计、循环次数可设定,时间可设定等功能! I Overview: This tester is widely used to test the abrasion resistance of the castors of the floor. By rubbing the floor samples with castors of a certain specification at a certain speed, a certain load and a certain movement path, the tester automatically stops after completing the accumulated test times to observe the changes of the samples and evaluate the abrasion resistance of the test samples. It has the functions of counting and accumulating the test cycles, setting the cycle times, and setting the time!
二,仪器参照标准标准: 、BS EN985-2001、ISO 4918-2009、ISO10581-2011等;2、 Reference standards for instruments: BS EN985-2001, ISO 4918-2009, ISO10581-2011, etc;
三,工作原理:
直径800mm钢转盘,上面贴一层7mm塑胶材料,试样750mm直径,每分钟转20圈;三个脚轮压在试样上面,负载90KG,脚轮盘自转每分钟50次;平台转动180秒后,暂停5秒,反向转动,如此反复运行,运行直到设定次数停止。
主要技術参数:
1、负载:90KG(可自行调整),脚轮盘自重10KG,砝码10kg*8个;
2、平台直径800mm;
3、试验转速:旋转台(20+0/-1)r/min,脚轮组件(50±1)r/min
4、计数器0-9999999次,可自行设定
5.控制方式:触摸屏PLC程序控制;
6、电 源:AC220V±22V,50Hz
7、功率约:2KW
3、 Working principle:
The steel turntable with a diameter of 800mm is pasted with a layer of 7mm plastic material, and the sample with a diameter of 750mm rotates 20 times per minute; Three castors are pressed on the sample with a load of 90KG, and the foot wheel rotates 50 times per minute; After the platform rotates for 180 seconds, pause for 5 seconds, reverse rotation, and repeat the operation until the set number of times stops.
Main technical parameters:
1. Load: 90KG (self adjustable), dead weight of foot wheel disc 10KG, weight 10kg * 8;
2. Platform diameter 800mm;
3. Test speed: rotary table (20+0/- 1) r/min, castor assembly (50 ± 1) r/min
4. Counter 0-9999999 times, self setting
5. Control mode: touch screen PLC program control;
6. Power supply: AC220V ± 22V, 50Hz
7. Power: about 2KW
三、安装操作注意事项:
1.试验机要安全接地线;测试时要远离试验机;测试时要注意脚轮变形情况,有问题要及时停机。
2.每次开机前先检查固定架紧固螺丝,确保锁紧;
3.测试时样品固定好
4.不允许超负荷、超速使用设备;
5.非工作时间应加护罩,长时间停歇,应定期进行擦拭,砝码负载杆加润滑油;
6.设备要放置平稳,防止振动移位。
7.测试时不要设置修改参数,停止后再设置。
企业类型 | 有限责任公司(自然人独资) | 统一社会信用代码 | 914419000923979136 |
---|---|---|---|
成立日期 | 2014-02-26 | 法定代表人/负责人 | 江红云 |
注册资本 | 600万(元) | 注册地址 | 广东省东莞市樟木头镇樟洋一村路726号3栋102室 |
营业期限 | 2014-02-26 至 无固定期限 | 登记机关 | 东莞市市场监督管理局 |
经营范围 | 产销:检测仪器设备。(依法须经批准的项目,经相关部门批准后方可开展经营活动)〓 |